Airport lighting, Apron Lighting

Airport LED Lighting, Apron Lighting, the best solution is as follows:

The hot-selling product our G3 is an advantageous choice for airport lighting. 

The asymmetric light pattern combined with the rotatable module design and the visor can make the lamps installed at 0° tilt, so as to achieve 0 upward light, making the sky over the airport safer. 

Our G3 of the high lumen can achieve the same required illuminance with fewer lamps and reduce costs. 

Because our G3 is small in size and light in weight, even if it is installed at a height of tens of meters, the wind resistance will be very small to reduce shaking.

Each LED module can be rotated individually to direct the light where it is needed. The luminous surface is not on the horizontal level, which can meet the requirements of the site more flexibly.

Portable & Mobile lighting for Emergency, Rescue & Sports field lighting

Portable & Mobile lighting for Emergency, Rescue & Sports field lighting
Mobile energy storage lighting devices, Light Towers, tower LED lights are suitable for outdoor use, and rental.

Suitable for some communities and the areas far away from City.

1. rechargeable battery：6000 KWH, 8000KWH, or 10000 KWH;

2. Liftable pole height：6 or 9 Meters.

3. Working temperature: -25℃（We'll update it to -40℃）

4. Design life：10Years

5. The total weight: 80Kgs±5%

6. Can be charged by mains electricity or solar energy panel.

7.There are many other functions, such as USB charge etc.

(Similar design to electric cars/ EV cars. )

DMX control RGBW LED Stadium lighting Solution

DMX control RGBW LED Stadium lighting Solution.

500W,600W,750W,900W,1000W,1200W,1500W,1800W.

TLCI>90, Broadcast Ready for >1500fps, HD丨8K, enable TV broadcasters to film super-slow-motion replays with a flicker factor <1%

Max Remote Distance Up to 300 Meters

Ultra-High Efficiency （Up to 97%）

No Afterglow

Dim-to-Off with Standby Power ≤ 0.5W @ 230Vac.

Dimming Range:0.4%-100%

3*600W Independent Programmable Channels & Support

Common Anode Output Connection

DALI-2 and D4i Certified & DMX-RDM & 3-Timer-Modes Dimmable

Single-channel (1*DT6 or 1*DMX) Operating Mode

DALI-2/DMX-RDM Controls Up to 33 fps

Integrated Power Metering with High Accuracy up to ±1%

high mast light for port near sea

Our certified lighting designers can upgrade or even retrofit your existing high mast light poles from older and energy-inefficient HID lighting to state-of-the-art LED high output lighting systems for maximum energy savings, lower maintenance costs, and minimized environmental effects, while delivering clean Kelvin daytime lighting levels. High mast light poles retrofitted for shipping ports, airports, rail yards, and high-ways over improved visibility and energy savings, moving from HID high-pressure sodium to clean daylight LED, which requires no maintenance and minimal lumen depreciation over years of operation.

Construction of LED luminaires vary depending on the type of light sources used, optics design, driver design, and thermal design. Essentially, the luminaire comprises an LED assembly, an LED driver, a die cast housing, and oftentimes, an additional electrical compartment. The LED assembly comes either in; an integrated design in which an LED board is thermally interfaced with the luminaire heat sink and protected by the luminaire housing and optical lenses against dust and moisture or a modular configuration in which the use of self-contained, waterproof light engines eliminates the need for the whole luminaire to be disassembled when there is a need for a modification or upgrade. 

Typically, the LED assembly comes equipped with secondary optics to regulate the distribution of luminous lux at package-level, although there're some products, such as, LED floodlights, using external refactors to control beam spread.

G3 LEDs Floodlight series for tennis

G3 LEDs Floodlight series for tennis
One School for Tennis

Best perfect performance installation of lighting 6 Tennis Courts at a large school.

Using quality G3 LEDs Floodlight series the installation was done to perfection.

G3 LED Floodlight replace the Philips 2000W MH and Gen series.

Our G3 LED Floodlight is an ideal solution to replace the Philips 2000W MH and Gen series for any retrofit projects and new projects.

If you are working closely with Philips, yes Philips are the market leader their product is very good, but their price is costly, and more customers would prefer cost-effective solution.

Our new generation flood light G3 has adapt compact size and high technology,1200w（single module） can easily replace the Philips 2000w MH lights, and this new model is up to 1800w（3 module） can replace Philips Gen3 flood light.

Main Product technology:

Single module up to 1200W,3module 1500W/1800W

(1) Compact size & light weight (1200W, net weight 21KG) very suitable for retrofit projects and new products.

(2) High output, up to 150lm/w, for standard pitch 200 lux (Class II) we just need 12 pcs 1200w fittings

(3) Compact size & small windage area （wind loads）: the width is only683mm, Philips 695mm,Siteco696mm,

(4) Advanced optical design reducing the spill light and glare rate.

Our G3 LED Floodlight is an ideal solution to replace the Philips 2000W MH and Gen series for any retrofit projects and new projects. with competitive price will help save a lot of money and enlarge more markets.

Bespoke solutions for outdoor lighting

Multiple installation method on options, Bespoke solutions for outdoor lighting.
A. Remote control Solution
1. One Lamp head comes with separate driver box, install under pole Neatly arranged on the light pole.
2. Lamp head up, and all LED Drivers installed in the distribution cabinet, under pole or ground.

B. Integral Driver Solution.

Cricket field lighting,1250w best bespoke solutions

 A cricket field or cricket oval is a large grass field on which the game of cricket is played. Although generally oval in shape, there is a wide variety within this: some are almost perfect circles, some elongated ovals and some entirely irregular shapes with little or no symmetry – but they will have entirely curved boundaries, almost without exception. There are no fixed dimensions for the field but its diameter usually varies between 450 and 500 feet (140 and 150 m) for men's cricket, and between 360 feet (110 m) and 420 feet (130 m) for women's cricket. Cricket is unusual among major sports (along with golf, Australian rules football and baseball) in that there is no official rule for a fixed-shape ground for professional games. On most grounds, a rope demarcates the perimeter of the field and is known as the boundary.

Within the boundary and generally as close to the centre as possible will be the square which is an area of carefully prepared grass upon which cricket pitches can be prepared and marked for the matches. The pitch is where batsmen hit the bowled ball and run between the wickets to score runs, while the fielding team tries to return the ball to either wicket to prevent this.

I'd like to share one of cricket field, comes with 30M height Pole, installed our 1250w, that result is perfect.

The following lighting calculations to this cricket field is for your reference.

Bespoke solutions for outdoor lighting, LED luminaire manufacturers, Specialist Exterior Lighting Contractors, Port Lighting, Airport Lighting, High Mast Lighting, Road Lighting, Sports Lighting, Area Lighting, Car Park Lighting, Highways Lighting, Street Lighting, and Apron Lighting

CCT and Power adjustable ip66 LED High Bay Light, new

CCT and Power adjustable ip66 LED High Bay Light, new

Our new power tunable plus color temperature tunable IP66 LED Bay Light, an innovative solution for commercial and industrial lighting applications. 

This versatile fixture offers adjustable brightness, color temperature, and IP66 waterproofing, making it ideal for a wide range of environments.

With its energy efficiency, long lifespan, and ease of installation, our power-tunable LED Bay Light is a valuable addition to any lighting project.

OEM for 1 one of the top brands in lighting, limited sharing.

 

Musco Knuckle Assembly bracket outdoor Sports LED light fixtures

Knuckle Assembly bracket outdoor Sports LED light fixtures,

Power:400W,500W,600W,630W,750W.

Multiple Beam Angle:12°/15°/25°/50°/25*105°/20°*40°-P10°/WB-P30°/NB-P55°/MB-P55°/VWB-P55°。

The best solution for your different field.

Small stadium, replace the Metal Halide 2000W with LEDs

Small stadium, replace the Metal Halide 2000W with LEDs.

110x60m small stadium,4x 22m poles, original lamp Metal Halide 2000W.

The stadium is 110X60 meters , with 4 poles , height 22 meter in the corners and at 5 meters distance away from the stadium and at 45 degree angle

metal halide 2000W and the current average lighting there is 180 lux.

Our 4x1000W,8x1200W, and 4x -600W LEDs Light fixtures work perfect.

The lighting solution for Steel or metal industry

The lighting solution for Steel or metal industry.

We're able to offer the lighting in extreme conditions solutions.

Lighting equipment is subjected to extreme conditions at industrial sites in the metal and steel sectors, where several types of requirements must be met to avoid shortening the service life of luminaires.

Intense heat, dust, vibrations, multi-factor corrosion, rust and sometimes explosive atmospheres (ATEX)... each metal production and transformation process brings particularly tough conditions which lighting equipment at the site must withstand. To avoid wasting time or capital in maintenance and replacing parts, it is essential to install solid and durable luminaires suitable for each area and the specific conditions in each zone.

1. Raw materials reception and agglomeration Areas

Raw materials are routed to and stored in these areas prior to crushing and sorting. The raw material reception and agglomeration area requires special consideration due to the scale and permanent nature of the vibrations produced by the large machines used to transport, extract and sort materials (railways, ships, excavators, giant hoppers, etc.). All equipment installed in this area must be compatible with the substantial amount of dust due to the handling of large volumes of materials.

Requirements

Intense and constant vibrations

Dust and dirt

Exposure to UVs and bad weather

Exposure to coastal corrosion

2. Coking plants, blast furnaces and steelworks

Extreme heat prevails at coking plants, blast furnaces and steelworks. Materials are melted and transformed at these sites. In addition to the technical challenge inherent in lighting located in an area with such high temperatures, it is also essential to consider the potential chemical damage caused by corrosive particles emitted by the materials and the transformation processes, not forgetting the explosive atmospheres (ATEX). The air in these areas is often contaminated with flammable particles (dust, gas); the electrical equipment used must therefore be totally reliable for obvious safety reasons.

Requirements

Extreme heat

Multi-factor corrosion

Explosive atmosphere (ATEX)

3. The continuous casting and strip mill(hot rolling)

The metal is heated, transformed, cooled, cut and treated with highly corrosive chemicals in this zone. Levels of corrosive vapours are high due to the nearby continuous casting and hot rolling belts.

Electrical disturbance must also be considered in this area due to the use of power machinery, requiring lighting equipment with reinforced electronics.

Requirements

Corrosion

Electrical disturbances

Heat

4. Emergency lighting

It is a legal imperative and safety requirement to install emergency lighting in the form of standalone luminaires (BAES), luminaires for central sources (LSC) or replacement lighting. This type of lighting guarantees that production areas, corridors and emergency exits at the industrial site are visible at all times if the power grid fails. For this reason, such lighting must comply with the applicable standards, be compatible with the environment in which it is installed and clearly be powered by a source other than the central power grid for the industrial site.

Requirements

Powered by a separate source to the main power grid

Suitable for the environmental conditions in the zone

Compliant with EN 60 598-2-22 and NF AEAS certified

Explosive atmospheres (ATEX)

5. Large outdoor areas (light brackets or posts, stair cases,etc.)

Large outdoor areas (car parks, stair cases, gangways, areas around buildings, etc.) must be lit to allow personnel to access and move around the industrial site safely. Such lighting is frequently installed in places that are particularly difficult to reach and often at height. To keep a cap on maintenance costs and optimise operating expenses, industrial sites must make sure that they install highly efficient, reliable and durable lighting equipment. It is also essential to ensure that the solutions installed are powerful enough for the area to be lit, with suitable photometry, providing adequate lighting levels spread evenly over the area to avoid shadows.

Requirements

Height

Complicated access

Efficient lighting levels and photometry

Exposure to UVs and bad weather

Exposure to coastal corrosion

22mt pole, football,600lux Average case Study.

22mt pole, football,600lux Average case Study.

This is Aaron who'd like to share a football field 22 mt pole, 600 LUX average ground lux as follows.

Superb installation of 1500W G3 LEDs Sports light fixtures on a refit of 22mt pole.

22-meter hight pole

600 lux average

Maintenance facture (LLF) 0.9

Uniformity Gradient > 0.7

IP66

IK （for ball impact）

Saltwater resistant 

Epoxy paint 

More than 4000K

CRI 80

Lifetime > 50,000

RG0

Flicker Free < 3%

The fittings came with a 7yr warrantee and marine paint as close to the sea.

Mobile energy storage lighting devices, Light Towers, tower LED light.

Mobile energy storage lighting devices, Light Towers, tower LED light.are suitable for outdoor use, and rental.

Suitable for some communities and the areas far away from City.

1. rechargeable battery：6000 KWH, 8000KWH, or 10000 KWH;

2. Liftable pole height：6Metersor 9 Meters;

3. Working temperature:-25℃ （We'll update it to -40℃）.

4. Design life：10Years

5. The total weight: 80Kgs±5%

6. Can be charged by mains electricity or solar energy panel;

7.There are many other functions, such as USB charge etc.

(Similar design to electric cars/ EV cars.)

CHAMPION G3 Series LED Flood Light

 CHAMPION G3 Series LED Flood Light

【Technical】

- Minimising windage of front and side surface through combined frame and modules . 

- Low total weight of complete system, same size with traditional 2000W Metal Halide/HPS. 

- Easy to intall and maintain, flexible mouting system especially the new IP66 driver box, absence of complex wiring between driver box and luminaire, also the modules. 

- Minimising TCO by maximum and constant light output with effective thermal management extend product lifetime and minimize maintenance costs. 

- LED uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. 

- Al1070 pure aluminum body, Seamless link of aerometal materials and numerous vents on heat sink improved heat management, keeps away from all field heat,ensures the stability of light system. 

- Salt-spray-tesing level 1000hours/2000hours/3000hours for your special projects requirements. 

- Equipped with 10KV/20KV SPD, resist huge grid surge.

【Optical】

-TLCI>90, Broadcast Ready for >1000fps, HD丨4K丨8K, enable TV broadcasters to film super-slow-motion replays with a flicker factor <1%

- Engineered by adopt seamless link of advanced Free-form optics.

- Optics designed with unique "multi scales lenses" to make uniform light distribution and glare-reducing.

- High transmittance PC cover, anti-UV, IK10 protective grade, prevent LED chips vulcanization and dust accumulation on the lens.

- Symmetrical and Asymmetrical light distribution enhancing uniformity of vertical and horizontal, meanwhile reducing light spill especially back pole light in residential area.

【Control】

- Scalable control solution, enables customisable, with real-time overrides and supports Art-Net, DMX RDM and DALI protocols.

- Support multi-Intelligent controls, WIFI, Zigbee.

【Application】

- Indoor Stadium丨Outdoor Stadium丨Wharf丨Apron Lighting丨Large Area Illumination 丨Tower Lighting | Sports Facility

How do we choose the best LED sports lights for tennis court?

 How do we choose the best LED sports lights for tennis court?

Tennis is a fast, multi-directional aerial sport. The tennis ball may approach the players at extremely high speed. Thus, while illuminance quantity and quality are most critical; illuminance uniformity, direct glare, and reflected glare come in a close second.

Our LED Sports lights optics are designed for tennis courts and can achieve the best results with the minimum number of sports lights. 

Class II level (4poles, 10M)

● 4X 750W LED Sports Flood Lights to reach Eav 500lx and 0.86 uniformity.

Class II level (10poles, 15M)

● 12X 900W LED Sports Flood Lights to reach Eav 400lx and 0.75uniformity.

Major events level (16poles, 10M)

● 40X 1200W LED Sports Flood Lights to reach Eav 1200lx and 0.65uniformity.

Our LED Sports lights provide uniform light, durable performance and can be used in a variety of harsh environments. 

LED sports floodlights are installed in tennis centers, stadiums and competition venues around the world.

Contact us on your next projects.

How to light up the tennis court?

How to light up the tennis court?
First of all, I'd like to share one of project with the perfect performance as follow.
3x tennis court lighting project, Avg Ground Lux> 500 lux

Our 8 x G3 1200W-NBP55 works perfectly.

Lighting up a tennis court requires proper planning and installation of suitable lighting fixtures that can provide adequate and uniform illumination for the players, spectators, and broadcasters. There are different types of lights that can be used for tennis court lighting, such as metal halide, high-pressure sodium, or LED lights. However, LED lights are considered the most efficient, durable, and eco-friendly option for tennis court lighting, as they can save energy, reduce maintenance, and improve visibility.

To light up a tennis court, you need to consider the following factors:

•  The size and shape of the court: The size and shape of the court determine the number and position of the light poles and fixtures. Generally, a standard tennis court is 36 feet wide and 78 feet long, with a 12-foot clearance on each side. For a single court, you may need four to six light poles, with two to three fixtures on each pole. For a double court, you may need six to eight light poles, with three to four fixtures on each pole.

•  The level and type of play: The level and type of play determine the lighting level and quality required for the court. Different levels and types of play have different lighting standards and specifications, according to the international or national governing bodies, such as the International Tennis Federation (ITF), the United States Tennis Association (USTA), or the Illuminating Engineering Society (IES). For example, recreational or residential play may need a lighting level of 30 to 50 footcandles (fc) or 300 to 500 lux, while professional or international play may need a lighting level of 100 to 150 fc or 1000 to 1500 lux.

•  The location and environment of the venue: The location and environment of the venue affect the lighting design and performance, as well as the environmental impact of the lighting system. For example, the latitude and longitude of the venue can determine the sun path and angle, which can influence the glare and shadow effects on the court. The climate and weather conditions of the venue can affect the durability and reliability of the lighting fixtures, as well as the energy consumption and carbon footprint of the lighting system.

To light up a tennis court, you can follow these steps:

•  Conduct a site survey and analysis: You need to measure and analyze the dimensions and conditions of the court, such as the length, width, height, orientation, slope, soil, drainage, etc. You also need to check the availability and accessibility of the power supply, wiring, and grounding. You also need to consider the surrounding environment, such as the buildings, trees, roads, etc., that may affect the lighting distribution and quality.

•  Choose the suitable lighting fixtures and accessories: You need to select the appropriate type, size, wattage, lumen output, beam angle, color temperature, color rendering index, and glare rating of the lighting fixtures for your court. You also need to choose the compatible mounting brackets, poles, wires, connectors, switches, sensors, controllers, etc., for your lighting system. You can refer to some online tools or guides, such as Sports Lighting Calculator Tennis Court Lighting Guide, to help you choose the best lighting solution for your court.

•  Design the lighting layout and plan: You need to design the optimal lighting layout and plan for your court, based on the lighting standards and specifications, as well as the site survey and analysis. You need to determine the number, position, height, angle, and spacing of the light poles and fixtures, as well as the wiring and control system. You can use some software or applications, such as DIALux or Visual, to help you design and simulate the lighting layout and plan for your court.

•  Install and test the lighting system: You need to install and test the lighting system for your court, according to the lighting layout and plan, as well as the safety and quality regulations. You need to follow the instructions and precautions of the lighting fixtures and accessories, as well as the electrical and structural codes. You also need to adjust and fine-tune the lighting fixtures and controllers, as well as measure and verify the lighting level and quality, to ensure the optimal lighting performance and effect for your court.

How to choose Sport Lighter?

How to choose Sport Lighter?

We have a large selection of outdoor LED Sport Lighters, there are G3 Series, ALTAS Series and ARES Series, the max Power 2250W. Light up the night!

Our factory offers a wide range of high Power LED Sport lighter able to light up any sports venue from Tennis Court to a UEFA Level A stadium, and everything in between. 

From the stock LED Sport Lighter to LED sport Lighter with custom optics, color temperature, shields, and all kinds of LED sport lighter accessories, we have what you need to light up your any sports venue. 

a. Optional remote LED drivers so most maintenance, while very rare, can be performed on or near the ground, instead of at the top of the pole.

b. LED sport lighter featuring EXTREME LIFE with L70 ratings as high as L70 at 250,000 hours, Standard 3,0000 Hours Salt-Spray Test, we provide the whole fixture 10 years warranty.

c. LOW WIND Resistance, lighter weight.

d.The asymmetric lenses ensure even light without glare or scattering. Our Lighting is able to provide Dark Sky Friendly lighting and anti-glare with stadium UEFA level A performance lighting, The optics are specially designed for Stadium, Field hockey, Tennis, Golf, Airport, etc.

While we have LED sports light packages for most sports venues, we recognize that many sports lighting projects are unique. That is why we have lighting specialists and lighting engineers to design and model the lighting to meet the requirements of your sports facility. 

Our factory has LED Sport lighter experience with tennis courts, soccer field, Baseball Field, Ice Hockey Field, Hockey Field, Football Field, Volleyball courts, Golf Course, Cricket Field, Bicycle Motocross Racing Field, Horse Racing courts, soccer fields, volleyball courts, swimming areas and UEFA Stadium, Olympic Stadium, riding arenas, baseball fields, and more. 

Contact us specialist immediately to see which kind of our LED Sport lighter will work best for your projects. ☝

HARMONY G3 LED Flood Light, Football field lighting solution

HARMONY G3 luminaire is professionally designed for football fields, its optical system allows efficient light to shine on the field, and is neighborhood friendly, without any spill light or sky glow. Special visors allow for better control of the upward light. 

The lighting standards of different events are also different, and HARMONY G3 is quite well applied in communities, high schools, colleges, 

universities, and even in large-scale games like NFL. 

We provide the best lighting solution for your sports fields to satisfy the player, spectator, community and environmental requirements.

Solution for High Mast Lighting

 For the lighting of large areas such as tourist and industrial ports, preferring the use of LED Food lighting means completely revising the concept of maintenance. 
Our LED Food lighting for ports and harbor lighting reach and exceed 100,000 hours or more than twenty years of operation. Forget the need for annual maintenance on light towers, such as changing traditional lighting lamps.

Adequate lighting and visibility also translate into greater safety, whether it is the handling of goods in an industrial port or the detection of obstacles in an airport parking area. Ensuring high visibility with high power LED Food lighting in these areas is essential.

Happy New Year 2024!

  Happy 2024 New Year!